CutChart / workshop reference
Can You Laser Cut Acrylic? Conditions Documented
6 quoted safety statements about acrylic, from xTool, Epilog Laser and Creality, last verified 2026-09-21. The cited publishers document operating conditions for this material, and CutChart shows them beside every settings row for it. Read the quotes in context before any job.
Quoted statements
- Fire:
Experience shows that vector cutting with a laser is most likely to produce an open flame. In particular, acrylic has proven to be extremely flammable in vector cutting.
(xTool, S1 Safety First (Important), read 2026-09-21) - Fire:
Many materials are susceptible to igniting; however, acrylic (in all its forms), has shown to be especially flammable when vector cutting with the laser.
(Epilog Laser, Reducing Fire Hazards with your Laser, read 2026-09-21) - Fire:
Utilizing the Air Assist feature will reduce the instance of flare-ups when working with flammable materials such as acrylic and wood.
(Epilog Laser, Reducing Fire Hazards with your Laser, read 2026-09-21) - Ventilation:
Ensure that the workspace is well-ventilated so that the generated smoke can be discharged in time.
(xTool, S1 Safety First (Important), read 2026-09-21) - Fire:
It is forbidden to leave it unattended while the machine is working.
(Creality, Creality Falcon2 (12W/22W/40W) User Manual, read 2026-09-21) - Check the composition:
Do not engrave or cut any unknown materials.
(xTool, S1 Safety First (Important), read 2026-09-21)
Reviewed 2026-09-21; expires 2026-12-20. These statements are quoted from the publishers named above and are not a complete safety procedure. The cited statements are not scoped to one laser family.
What CutChart publishes for this material
The settings reference for acrylic carries these statements beside every row: start from the acrylic settings hub. A row always names the machine it was printed for.
Common questions
Did CutChart test this material?
No. Every statement on this page is quoted from the publisher named beside it, with the document title and the date CutChart read it. CutChart has purchased no machine and run no test.
Why does a material have no settings table?
CutChart publishes a settings row only when a sourced material-safety record exists for the material. A material whose cited publisher says not to laser it gets a warning and no settings, whatever its laser family.
What does the review date mean?
Each record states the day CutChart last verified its quoted statements against the publisher document and the day that verification expires. Re-reading a source after its expiry window is a scheduled job, not a claim about the publisher.
Source documents
3 documents behind the rows and safety statements on this page. Open a document to read every excerpt as printed.
Epilog Laser: Reducing Fire Hazards with your Laser (2 excerpts)
Reducing Fire Hazards with your Laser
Publication date not printed by Epilog Laser · Read · Captured
Many materials are susceptible to igniting; however, acrylic (in all its forms), has shown to be especially flammable when vector cutting with the laser.
Epilog Laser, Reducing Fire Hazards with your Laser, Introduction. Publication date not printed by Epilog Laser · Read · Captured . Read the named field and section in the cited document. The excerpt alone does not establish a complete cutting procedure.
Utilizing the Air Assist feature will reduce the instance of flare-ups when working with flammable materials such as acrylic and wood.
Epilog Laser, Reducing Fire Hazards with your Laser, Warnings and Recommendations. Publication date not printed by Epilog Laser · Read · Captured . Read the named field and section in the cited document. The excerpt alone does not establish a complete cutting procedure.
Creality: Creality Falcon2 (12W/22W/40W) User Manual (1 excerpt)
Creality Falcon2 (12W/22W/40W) User Manual
Publication date not printed by Creality · Read · Captured
14. It is forbidden to leave it unattended while the machine is working.
Creality, Creality Falcon2 (12W/22W/40W) User Manual, Security Statement. Publication date not printed by Creality · Read · Captured . Read the named field and section in the cited document. The excerpt alone does not establish a complete cutting procedure.
xTool: S1 Safety First (Important) (3 excerpts)
Publication date not printed by xTool · Read · Captured
A high-density laser beam is used by the device to irradiate the material to be cut or engraved, so as to heat up the material surface and vaporize the material without burning. But most materials are inherently flammable and may be ignited to form an open flame that can burn down the device (even if it is made of flame-retardant materials) and its surroundings. Experience shows that vector cutting with a laser is most likely to produce an open flame. In particular, acrylic has proven to be extremely flammable in vector cutting.
xTool, S1 Safety First (Important), 3. Fire safety. Publication date not printed by xTool · Read · Captured . Read the named field and section in the cited document. The excerpt alone does not establish a complete cutting procedure.
Do not engrave or cut any unknown materials. Vaporization or melting of many materials, which include but are not limited to PVC and polycarbonate, may release harmful smoke.
xTool, S1 Safety First (Important), 2. Laser safety. Publication date not printed by xTool · Read · Captured . Read the named field and section in the cited document. The excerpt alone does not establish a complete cutting procedure.
Ensure that the workspace is well-ventilated so that the generated smoke can be discharged in time.
xTool, S1 Safety First (Important), 3. Fire safety. Publication date not printed by xTool · Read · Captured . Read the named field and section in the cited document. The excerpt alone does not establish a complete cutting procedure.
Reference information only. Follow the instructions for your exact machine and material. A listed setting does not establish that a job is safe. Read the safety limits.